Kirpa Digital Catalog

OverviewThe sleek, exotic-looking body has koa and rosewood over mahogany the maple neck has a pau ferro fingerboard with Posiflex™ graphite neck support rods, abalone dot inlays, rolled fingerboard edges and highly detailed nut and fret work. Two Samarium Cobalt Noiseless™ 5-String Jazz Bass pickups add warmth and low end, complementing the hardwood bodys natural clarity and brightness and producing an extremely dynamic tonal range. The circuitry has been tweaked at the input stage (pre-shape, boost and EQ settings) to enhance the unique sonic nature of the woods. Bass EQ is centered at 40Hz 12dB with a 4dB per-octave slope treble is centered at 8 kHz 10dB with a 2dB per-octave slope (treble cut serves more as a passive control for warm organic tones) mid-control is centered at 500Hz and +10dB and -15dB with a wide-band slope creating a distinctive voice. For maximum headroom, the circuit has an 18-volt power supply.

This portable SPL meter features a built-in condenser mic and digital display. It accurately measures the sound level of just about anything from PA systems to car audio (accuracy +/-2dB).

DO YOU HAVE SIGNAL PROBLEM?We have a solution for you. THIS AMPLIFIER IS ONLY FOR NEXTEL iDEN PHONES Free Shipping in the U.S.A! The Wilson bi-directional cellular amplifier / repeater greatly improves signal strength inside a building when using your cell phone. It does this without physical connection to your phone allowing you to walk around freely during a call. It even allows multiple phones to be used simultaneously. The signal is received by the outside antenna from the cell site. It is then amplified and repeated to your cell phone through the inside antenna. When the phone transmits, the signal is received by the inside antenna, amplified, then repeated to the cell site via the outside antenna. Installation Options: Option A (In-buildings, home, office, warehouse and more) Requirements needed (sold separately) Outside antenna (recommend Yagi) Inside antenna (recommend Ceiling Mount Dome Antenna) Ultra Low Loss Cable Antenna and Accessory Options Dual-Band Panel Antenna (301135) Low Profile Antenna (301106) Mini Magnet Antenna (301113) Trucker Mirror Mount Antenna (301101) 2-Way Splitter (859901) 20' Coax Cable (9913) 50' Coax Cable (9913) Wilson In-Building Wireless iDEN 50 dB Amplifier (804005) features For iDEN frequencies Increases signal strength in buildings for iDEN (Nextel, Southern LINC, Mike) frequencies (806-866MHz) (check compatibilites below) Power control logic ensures maximum output power is within cellular network standards Automatic shutdown on overload Oscillation detection and gain reduction with auto reset intervals AC power supply included FCC and IC type accepted Greater than 50dB computer controlled adjustable AGC dynamic range Automatic Gain Adjusting in the event of oscillation and/or overload 2dB Gain Steps (20 - 50dB) TIA/EIA-98-E 3.5.1 Receiver Sensitivity better than -110 dBm Wireless operation - no physical connection to cellular phone Maximum 3 Watts Output Power High Power Output Allows More Users on the System Allows multiple phones to be used simultaneously Increases your cellular phone's range Low cost solution for uncompromised performance Overload Protection on Uplink and Downlink Receive/Transmit Overload Indicator Lights Low Isolation Indicator Also works for direct connect communication  Wilson In-Building Wireless iDEN 50 dB Amplifier (804005) specifications Part Number: 804005 Frequency: 806-821 MHz / 851-866 MHz Gain: 50 dB Max Output Power: up to 3 watts Max RF: + 30 dBm / + 30 dBm Noise Figure: 3 dB nominal Flatness: ? 2.5 dB Isolation: > 90 dB Power Requirements: 120 V AC 3 A max Connectors: N-Female 50 ohms Dimensions: 5.6 x 3.6 x 1.7(inches) / 14.2 x 9.1 x 4.4 (cm) Weight: 1.5 lbs / 0.7 kg For more information about Installation and Specifications, check out the Wilson Brochure below: *A cell phone using our amplifier is